While the LM25066I/A is functionally similar to the LM25066/A, the LM25066I/A is fully compliant to Intel Node Manager 2.0, 2.5 and adds the READ_EIN energy accumulator feature. The LM25066I/A combines a high-performance hot-swap controller with a PMBus 1.2^™ compliant SMBus/I²C interface to accurately measure, control and protect the electrical operating conditions of critical systems. The LM25066I/A continuously supplies real-time power, voltage, current, temperature, and fault data to the system management host via the SMBus interface.

The LM25066I/A control block includes a unique hot-swap architecture that provides current and power limiting to protect sensitive circuitry even during the most stressful conditions. A fast-acting circuit breaker prevents damage in the event of a short circuit on the output. The input under-voltage, over-voltage hysteresis, insertion delay time and fault detection time are all configurable. A temperature monitoring block on the LM25066I/A interfaces with a low-cost external diode for continuous temperature assessment of the external MOSFET or other thermal sensitive components. The POWER GOOD output provides a fast alert when the input and/or output voltages are outside their programmed range. Accurate power readings are accomplished by using the READ_EIN command. A black box (Telemetry/Fault Snapshot) function captures and stores telemetry data and device status in the event of a warning or a fault.

• Fully Node Manager 2.0 and 2.5 Compliant with I2C/SMBus interface and PMBus compliant command structure
• Input voltage range: 2.9V to 17V
• Programmable 25mV or 46mV current limit threshold
• Read_EIN accurately measures true input power via simultaneous sampling
• Configurable circuit breaker protection for hard shorts
• Configurable under- and over-voltage lockouts with hysteresis
• Real time monitoring of VIN, VOUT, IIN, PIN, VAUX with 12-bit resolution and 1 kHz sampling rate
• Current measurement accuracy: ±1% (LM25066IA) and Power measurement accuracy: ±2.0% (LM25066IA) over temperature
• Averaging of VIN, IIN, PIN, and VOUT over programmable interval ranging from 0.001 to 4 seconds
• Programmable WARN and FAULT thresholds with SMBA notification
• Blackbox capture of telemetry measurements and device status triggered by WARN or FAULT condition
• 24-lead WQFN package

All trademarks are the property of their respective owners.

• FET
• External
• Vin (Min) (V)
• 2.9
• Vin (Max) (V)
• 17
• Vabsmax_cont (V)
• 24
• Current limit (Min) (A)
• 0.01
• Current limit (Max) (A)
• 500
• Overcurrent response
• Circuit breaker, Current limiting
• Fault response
• Auto-retry, Latch-off

LM25066IA的完整型号有：LM25066IAPSQ/NOPB、LM25066IAPSQE/NOPB、LM25066IAPSQX/NOPB，以下是这些产品的关键参数及官网采购报价：

LM25066IAPSQ/NOPB，工作温度：-40 to 125，封装：WQFN (NHZ)-24，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网LM25066IAPSQ/NOPB的批量USD价格：2.357（1000+）

LM25066IAPSQE/NOPB，工作温度：-40 to 125，封装：WQFN (NHZ)-24，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网LM25066IAPSQE/NOPB的批量USD价格：2.357（1000+）

LM25066IAPSQX/NOPB，工作温度：-40 to 125，封装：WQFN (NHZ)-24，包装数量MPQ：4500个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网LM25066IAPSQX/NOPB的批量USD价格：1.964（1000+）

PI-Commander EVM GUI

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

LM25066 Design Calculator With FET Recommendation

PMP11399 是完整的 PMBus 电力系统，可以为 3 个 ASIC/FPGA 内核、DDR3 内核内存、VTT 终端供电，并为高性能以太网交换机提供辅助电压。硬件附带有 GUI，便于用户对电源执行实时配置和监控。