The LM26LV and LM26LV-Q1 are low-voltage, precision, dual-output, low-power temperature switches and temperature sensors. The temperature trip point (T_TRIP) can be preset at the factory to any temperature in the range of 0°C to 150°C in 1°C increments. Built-in temperature hysteresis (T_HYST) keeps the output stable in an environment of temperature instability.

In normal operation the LM26LV or LM26LV-Q1 temperature switch outputs assert when the die temperature exceeds T_TRIP. The temperature switch outputs will reset when the temperature falls below a temperature equal to (T_TRIP – T_HYST). The OVERTEMP digital output, is active-high with a push-pull structure, while the OVERTEMP digital output, is active-low with an open-drain structure.

The analog output, V_TEMP, delivers an analog output voltage with Negative Temperature Coefficient (NTC).

Driving the TRIP_TEST input high causes the digital outputs to be asserted for in-situ verification and causes the threshold voltage to appear at the VTEMP output pin, which could be used to verify the temperature trip point.

The LM26LV’s and LM26LV-Q1’s low minimum supply voltage makes them ideal for 1.8-V system designs. The wide operating range, low supply current, and excellent accuracy provide a temperature switch solution for a wide range of commercial and industrial applications.

• Low 1.6-V Operation
• Low Quiescent Current
• Latching Function: Device Can Latch the Over Temperature Condition
• Push-Pull and Open-Drain Temperature Switch Outputs
• Wide Trip Point Range of 0°C to 150°C
• Very Linear Analog VTEMP Temperature Sensor Output
• VTEMP Output Short-Circuit Protected
• Accurate Over 50°C to 150°C Temperature Range
• Excellent Power Supply Noise Rejection
• LM26LVQISD-130 and LM26LVQISD-135 are AEC-Q100 Qualified and are Manufactured on an Automotive Grade Flow:
  • Device Temperature Grade 0: 40°C to 150°C Ambient Operating Temperature Range
  • Device HBM ESD Classification Level 3 A
  • Device CDM ESD Classification Level C6
  • Device MM ESD Classification Level M3

• SetPoint type
• Factory Programmed
• SetPoint value (deg C)
• 0 to 150, 130, 135
• Operating temperature range (C)
• -40 to 150
• Accuracy over temp range (Max) (C)
• 2.3
• Sensor gain (mV/Deg C)
• -5.1 to -12.8
• Output type
• Open Drain, Push Pull
• Supply voltage (Min) (V)
• 1.6
• Supply voltage (Max) (V)
• 5.5
• Supply current (Typ) (uA)
• 8
• Comparator channels (#)
• 1
• Features
• Built-in hysteresis
• Rating
• Automotive
• Interface type
• Analog output, Switch

LM26LV-Q1的完整型号有：LM26LVQISD-130/NOPB、LM26LVQISDX-130/NOPB、LM26LVQISDX-135/NOPB，以下是这些产品的关键参数及官网采购报价：

LM26LVQISD-130/NOPB，工作温度：-40 to 150，封装：WSON (NGF)-6，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM26LVQISD-130/NOPB的批量USD价格：.435（1000+）

LM26LVQISDX-130/NOPB，工作温度：-40 to 150，封装：WSON (NGF)-6，包装数量MPQ：4500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM26LVQISDX-130/NOPB的批量USD价格：.372（1000+）

LM26LVQISDX-135/NOPB，工作温度：-40 to 150，封装：WSON (NGF)-6，包装数量MPQ：4500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM26LVQISDX-135/NOPB的批量USD价格：.478（1000+）

LM26LVEVM LM26LV 出厂预设跳变点、工作电压为 1.6V 的温度传感器开关评估模块

LM26LVEVM 允许用户评估具有工厂程控跳闸点和温度传感器的 LM26LV 温度开关的性能。LM26LVEVM 随附工厂编程为在 80°C 时跳闸的 LM26LV 并随附用于探测 LM26LV 引脚的接头。