The TL16C2550 is a dual universal asynchronous receiver and transmitter (UART). It incorporates the functionality of two TL16C550D UARTs, each UART having its own register set and FIFOs. The two UARTs share only the data bus interface and clock source, otherwise they operate independently. Another name for the uart function is Asynchronous Communications Element (ACE), and these terms will be used interchangeably. The bulk of this document describes the behavior of each ACE, with the understanding that two such devices are incorporated into the TL16C2550.

Each ACE is a speed and voltage range upgrade of the TL16C550C, which in turn is a functional upgrade of the TL16C450. Functionally equivalent to the TL16C450 on power up or reset (single character or TL16C450 mode), each ACE can be placed in an alternate FIFO mode. This relieves the CPU of excessive software overhead by buffering received and to be transmitted characters. Each receiver and transmitter store up to 16 bytes in their respective FIFOs, with the receive FIFO including three additional bits per byte for error status. In the FIFO mode, a selectable autoflow control feature can significantly reduce software overload and increase system efficiency by automatically controlling serial data flow using handshakes between the RTS output and CTS input, thus eliminating overruns in the receive FIFO.

Each ACE performs serial-to-parallel conversions on data received from a peripheral device or modem and stores the parallel data in its receive buffer or FIFO, and each ACE performs parallel-to-serial conversions on data sent from its CPU after storing the parallel data in its transmit buffer or FIFO. The CPU can read the status of either ACE at any time. Each ACE includes complete modem control capability and a processor interrupt system that can be tailored to the application.

Each ACE includes a programmable baud rate generator capable of dividing a reference clock with divisors from 1 to 65535, thus producing a 16× internal reference clock for the transmitter and receiver logic. Each ACE accommodates up to a 1.5-Mbaud serial data rate (24-MHz input clock). As a reference point, that speed would generate a 667-ns bit time and a 6.7-µs character time (for 8,N,1 serial data), with the internal clock running at 24 MHz.

Each ACE has a TXRDY and RXRDY output that can be used to interface to a DMA controller.

• Programmable Auto-RTS and Auto-CTS
• In Auto-CTS Mode, CTS Controls Transmitter
• In Auto-RTS Mode, RCV FIFO Contents, and Threshold Control RTS
• Serial and Modem Control Outputs Drive a RJ11 Cable Directly When Equipment Is on the Same Power Drop
• Capable of Running With All Existing TL16C450 Software
• After Reset, All Registers Are Identical to the TL16C450 Register Set
• Up to 24-MHz Clock Rate for up to 1.5-Mbaud Operation With VCC = 5 V
• Up to 20-MHz Clock Rate for up to 1.25-Mbaud Operation With VCC = 3.3 V
• Up to 16-MHz Clock Rate for up to 1-Mbaud Operation With VCC = 2.5 V
• Up to 10-MHz Clock Rate for up to 625-kbaud Operation With VCC = 1.8 V
• In the TL16C450 Mode, Hold and Shift Registers Eliminate the Need for Precise Synchronization Between the CPU and Serial Data
• Programmable Baud Rate Generator Allows Division of Any Input Reference Clock by 1 to (2 16 -1) and Generates an Internal 16 × Clock
• Standard Asynchronous Communication Bits (Start, Stop, and Parity) Added to or Deleted From the Serial Data Stream
• 5-V, 3.3-V, 2.5-V, and 1.8-V Operation
• Independent Receiver Clock Input
• Transmit, Receive, Line Status, and Data Set Interrupts Independently Controlled
• Fully Programmable Serial Interface Characteristics:
  • 5-, 6-, 7-, or 8-Bit Characters
  • Even-, Odd-, or No-Parity Bit Generation and Detection
  • 1-, 1 1/2-, or 2-Stop Bit Generation
  • Baud Generation (DC to 1 Mbit/s)
• False-Start Bit Detection
• Complete Status Reporting Capabilities
• 3-State Output TTL Drive Capabilities for Bidirectional Data Bus and Control Bus
• Line Break Generation and Detection Internal Diagnostic Capabilities:
  • Loopback Controls for Communications Link Fault Isolation
  • Break, Parity, Overrun, and Framing Error Simulation
• Fully Prioritized Interrupt System Controls
• Modem Control Functions (CTS, RTS, DSR, DTR, RI, and DCD)
• Available in 48-Pin TQFP (PFB) Package, 32-Pin QFN (RHB), or 44-Pin PLCC (FN) Package
• Pin Compatible with TL16C752B (48-Pin Package PFB)

• Number of channels (#)
• 2
• FIFOs (bytes)
• 16
• Rx FIFO trigger levels (#)
• 4
• Tx FIFO trigger levels (#)
• —
• Programmable FIFO trigger levels
• No
• CPU interface
• X86
• Baud rate (max) at Vcc = 1.8 V & with 16X sampling (Mbps)
• 0.625
• Baud rate (max) at Vcc = 2.5 V & with 16X sampling (Mbps)
• 1
• Baud rate (max) at Vcc = 3.3 V & with 16X sampling (Mbps)
• 1.25
• Baud rate (max) at Vcc = 5.0 V & with 16X sampling (Mbps)
• 1.5
• Operating voltage (V)
• 1.8, 2.5, 3.3, 5
• Auto RTS/CTS
• Yes
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85, 0 to 70

TL16C2550的完整型号有：TL16C2550IPFB、TL16C2550IPFBR、TL16C2550IRHB、TL16C2550IRHBR、TL16C2550PFB、TL16C2550PFBR、TL16C2550RHB、TL16C2550RHBR，以下是这些产品的关键参数及官网采购报价：

TL16C2550IPFB，工作温度：-40 to 85，封装：TQFP (PFB)-48，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550IPFB的批量USD价格：2.935（1000+）

TL16C2550IPFBR，工作温度：-40 to 85，封装：TQFP (PFB)-48，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550IPFBR的批量USD价格：2.465（1000+）

TL16C2550IRHB，工作温度：-40 to 85，封装：VQFN (RHB)-32，包装数量MPQ：73个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550IRHB的批量USD价格：2.935（1000+）

TL16C2550IRHBR，工作温度：-40 to 85，封装：VQFN (RHB)-32，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550IRHBR的批量USD价格：2.465（1000+）

TL16C2550PFB，工作温度：0 to 70，封装：TQFP (PFB)-48，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550PFB的批量USD价格：2.935（1000+）

TL16C2550PFBR，工作温度：0 to 70，封装：TQFP (PFB)-48，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550PFBR的批量USD价格：2.465（1000+）

TL16C2550RHB，工作温度：0 to 70，封装：VQFN (RHB)-32，包装数量MPQ：73个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550RHB的批量USD价格：2.935（1000+）

TL16C2550RHBR，工作温度：0 to 70，封装：VQFN (RHB)-32，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TL16C2550RHBR的批量USD价格：2.465（1000+）

TL16C2550 2.5V PFB PKG IBIS Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)