The TLC59581/82are 48-channel constant-current sink drivers. Each channel has an individually-adjustable, 65536-step, pulse width modulation (PWM) grayscale (GS) brightness control.

The TLC59581 can support 32-multiplexing while TLC59582 can support 16-multiplexing.

The output channels are divided into three groups. Each group has a 512-step color brightness control (CC). CC adjusts brightness control between colors. The maximum current value of all 48 channels can be set by 8-step global brightness control (BC). BC adjusts brightness deviation between LED drivers. GS, CC and BC data are accessible through a serial interface port.

See application note Build High Density, High Refresh Rate, Multiplexing LED Panel with TLC59581, SLVA744.

The TLC59581/82 device has one error flag: the LED open detection (LOD), which can be read through a serial interface port. To resolve this caterpillar issue caused by an open LED, the TLC59581/82 device has an enhanced circuit for caterpillar canceling, thermal shut down (TSD) and I_REF resistor short protection (ISP), which ensures a higher system reliability. The TLC59581/82 device also has a power-save mode that sets the total current consumption to 0.8 mA (typical) when all outputs are off. The TLC59581/82 device is a good solution to improve display performance of a multiplexing panel for low-grayscale patterns.

• 48 Constant-Current Sink Output Channels
• Sink Current Capability with Max BC/CC data:
  • 25 mA at 5 VCC
  • 20 mA at 3.3 VCC
• Global Brightness Control (BC): 3-Bit (8-Step)
• Color Brightness Control (CC) for Each Color Group: 9-Bit (512-Step), Three Groups
• LED Power Supply Voltage Up To 10 V
• VCC = 3.0 V to 5.5 V
• Constant Current Accuracy
  • Channel-to-Channel = ±1%(Typ), ±3%(Max)
  • Device-to-Device = ±1%(Typ), ±2%(Max)
• Data Transfer Rate: 25 MHz
• Gray Scale Clock: 33 MHz
• Pre-Charge FET to Avoid Ghosting Phenomenon
• Enhanced Circuit for Caterpillar Cancelling
• Low-Grayscale Enhancement
• LED Open Detection (LOD)
• Thermal Shut Down (TSD)
• Operating Temperature: 40°C to 85°C

• Features
• 48CH LED Driver, Error Flag, Fault Detection, LED Open Detection, PWM LED Driver, Pre-Charge FET, SRAM, Thermal Shutdown
• Analog dimming steps
• 512
• Data transfer rate (Typ) (MHz)
• 25
• Ch to ch accuracy (Typ) (+/- %)
• 1
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85

TLC59582的完整型号有：TLC59582RTQR、TLC59582RTQT，以下是这些产品的关键参数及官网采购报价：

TLC59582RTQR，工作温度：-40 to 85，封装：QFN (RTQ)-56，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAUAG，TI官网TLC59582RTQR的批量USD价格：2.47（1000+）

TLC59582RTQT，工作温度：-40 to 85，封装：QFN (RTQ)-56，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TLC59582RTQT的批量USD价格：2.954（1000+）

PSPICE-FOR-TI 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TIDA-00161 具有高多路复用功能的 64x64 全色 (R/G/B) LED 矩阵

此参考设计是具有 TLC5958 驱动器 IC 的完整 64 像素 x 64 像素红/绿/蓝 LED 面板。
由于其更高的集成度和高度的时间多路复用支持，此设计仅通过 8 个 TLC5958 IC 即可提供总计 12,288 个单独的 LED 灯（= 64 x 64 x 3 色）。此 LED 面板仍保持非常高的视频输出质量。