The TPS6130xx device is based on a high-frequency synchronous boost topology with constant current sinks to drive up to three white LEDs in parallel (400-mA, 800-mA, and 400-mA maximum flash current). The extended high-current mode (HC_SEL) allows up to 1025-mA, 2050-mA, and 1025-mA flash current out of the storage capacitor.

The high-capacity storage capacitor on the output of the boost regulator provides the high-peak flash LED current, thereby reducing the peak current demand from the battery to a minimum.

The 2-MHz switching frequency allows the use of small and low profile 2.2-µH inductors. To optimize overall efficiency, the device operates with a 400-mV LED feedback voltage.

The TPS6130xx device not only operates as a regulated current source, but also as a standard voltage boost regulator. The device keeps the output voltage regulated even when the input voltage exceeds the nominal output voltage. The device enters power-save mode operation at light load currents to maintain high efficiency over the entire load current range.

To simplify flashlight synchronization with the camera module, the device offers a trigger pin (FLASH_SYNC) for zero latency LED turnon time.

• Four Operational Modes
  • DC Light and Flashlight
  • Voltage Regulated Converter: 3.8 V to 5.7 V
  • Standby: 2 μA (Typical)
• Storage Capacitor Friendly Solution
• Automatic VF and ESR Calibration
• Power-Save Mode for Improved Efficiency at Low Output Power, Up to 95% Efficiency
• Output Voltage Remains Regulated When Input Voltage Exceeds Nominal Output Voltage
• I2C Compatible Interface up to 3.4 Mbits/s
• Zero Latency Tx-Masking Input
• Hardware Voltage Mode Selection Input (TPS61300, TPS61301)
• DC Light Mode Selection Input (TPS61300, TPS61306)
• Hardware Reset Input (TPS61301, TPS61305)
• LED Temperature Monitoring (TPS61305)
• Privacy Indicator LED Output
• Integrated LED Safety Timer
• Total Solution Size of Less Than 25 mm2 (< 1 mm height)
• Available in a 20-Pin NanoFree? (DSBGA)

• Input voltage (type)
• DC/DC
• Topology
• Boost, Current Mode
• Vin (Min) (V)
• 2.5
• Vin (Max) (V)
• 5.5
• Iout (Max) (A)
• 1.5
• Iq (Typ) (mA)
• 0.59
• Features
• Load Disconnect During Shutdown
• Operating temperature range (C)
• -40 to 85
• Dimming method
• Analog, PWM

TPS61301的完整型号有：TPS61301YFFR、TPS61301YFFT，以下是这些产品的关键参数及官网采购报价：

TPS61301YFFR，工作温度：-40 to 85，封装：DSBGA (YFF)-20，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网TPS61301YFFR的批量USD价格：.85（1000+）

TPS61301YFFT，工作温度：-40 to 85，封装：DSBGA (YFF)-20，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网TPS61301YFFT的批量USD价格：1.02（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)